Stepper motor control
Stepper motor controllers for a wide variety of applications.
- 1 Axis Bipolar Stepper Motor Driver$68.95 As low as $62.50
SKU: KTA-261
Small 1, 2 or 3 axis stepper motor drivers with full, 1/2, 1/4 and 1/16 micro-step modes. Learn More - 1 Ch USB Stepper Motor Card$67.95
SKU: K8096
While the motor turns you can simultaneously check the status of the dry-inputs (ex. emergency stop signal, limit detection...). Learn More - 16 tooth timing pulley 5mm ID 9.5mm OD.$2.95
SKU: GT230
Aluminum toothed drive pulley, get a grip! 6mm wide 9.5MM diameter 16 teeth 5mm hole. Learn More - 4 wire 100CM Dupont cable with NEMA17 stepper motor connection$1.95 As low as $1.60
SKU: 4WN17DP100
4 wire 100CM Dupont cable with NEMA17 stepper motor connection Learn More - 4 wire 72CM Dupont cable with NEMA17 stepper motor connection$1.75 As low as $1.50
SKU: 4WN17DP72
4 wire 72CM Dupont cable with NEMA17 stepper motor connection Learn More - 5 volt stepper motor and simple driver works with a micro$5.95 As low as $5.00
SKU: STPRDRV
5 volt stepper motor and transistor driver Learn More - A4988 Stepper Motor Driver Board$3.50 As low as $3.00
SKU: A4988-1
A4988 clone stepper motor driver. Please read the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.0 A output current per coil.
Learn More - Bipolar Stepper Motor Controller$34.95 As low as $29.95
SKU: KT-5196A
KTA-196 or KT-5196A
This Bipolar Stepper Motor Controller is Microcontroller Based
Controls 4, 6 and 8 wire Stepper Motors
Full and Half Stepping Modes Learn More -
-
- Flexible coupler for steppers or other 5mm and 8mm shafts.$1.95
SKU: FLX58MM
Aluminum machined flexible shaft coupler. 5MM to 8MM Learn More - GT2 16 tooth Timing Pulley Kit$9.50
SKU: GT2KIT
Aluminum Timing Belt Pulley GT2 16 Teeth Bore 5mm Width 6mm for 3D printer parts with Wrench- 10 Pack Learn More - GT2 6mm Belt for 3D Printer$2.50
SKU: GT26MMTB
GT2 6mm Belt for 3D printer. 6mm x your length (by the meter) Learn More - GT2 Closed Loop Timing Belt$2.14
SKU: GT2610
GT2 Timing Belt for 3D printer. 6mm x 610mm Learn More - H4988 Stepper Motor Driver Board$3.95 As low as $3.00
SKU: H4988
A4988 clone stepper motor driver. Please read the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.0 A output current per coil.
Learn More - L298N Motor Driver Module$5.95 As low as $4.95
SKU: L298N
This Arduino Compatible Stepper Motor Driver Controller Board uses L298N Driver IC. DATA SHEET
Stepper Motor in photo is not included.
Learn More - L298P Motor Driver Shield$9.95
SKU: L298P
This Arduino Compatible Stepper Motor Driver Controller Board uses L298P Driver IC. Learn More - Limit switch with 50 cm cable lever on the micro switch LSW2$2.50 As low as $2.00
SKU: LSW2
limit switch 3d printer with cable Learn More - LM2903 Dual Differential Comparator 8 P DIP$1.25 As low as $1.00
SKU: LM2903
LM2903 Dual Differential Comparator Plastic DIP Learn More - LV8729 Motor Stepper Driver Board$7.95
SKU: LV8729
MKS LV8729 stepper motor driver 4-layer substrate ultra quiet driver LV8729 driver support 6V-36V full microstep driver controller Learn More -
- Programmable Stepper Motor Controller$74.95
SKU: KT-5193A
KTA-193 or KT-5193AThe Modbus Programmable Stepper Motor Controller is a four axis multifunction programmable stepper motor controller which utilises the modbus protocol for communications. Learn More
- Serial Bipolar Stepper Motor Driver$54.95
SKU: KT-5197A
KTA-197 or KT-5197AYou simply write ascii commands through the PC's serial port to the card to control each of the stepper motors Learn More
- Stepper Driver H4988 DRV8825 breakout board$3.49
SKU: STPBB
H4988 or DRV8825 (NOT included) Stepper Driver Board and breakout board for your 3D Printing, Arduino, Robotics, Raspberry Pi or other projects Learn More
Please complete your information below to login.
Sign In
Create New Account