Product Description
Details
To order kit version, Click Here
To order polled version, Click Here
Free software for the VK011 written by Jeff Connolly
Allows each temperature sensor to be displayed in its own window with assignable colors for over under temperature conditions. You can select Celsius or Fahrenheit and the number of digits for precision. Saves its setting on exit and allows you to select any COM port not just COM ports 9 and down. Requires .NET framework Version 2.
Allows large Fonts that can be viewable using a CCTV camera for remote monitoring.
New Version has the ability to drive serial relay cards, QK108, VK013 and so on, with logging to a text file.
VK011 PDF manual
Specifications
Power Requirements
* 9 - 15vDC (from adaptor or through the serial port)
* Screw terminals for easy connection of up to four Dallas DS18S20 temperature sensors (One DS18S20 sensor included)
Additional
* Measures in both degrees C (Celcius), and degrees F (Fahrenheit)
* Adjustable sample rate from 1 second to 99 seconds, or 1 minute to 99 minutes
* Advanced CRC error checking
* Will alert you to a short or disconnection in a sensor, and which one
* Setup menu helps in locating faulty devices by displaying accumulated CRC errors and current status of data along with serial number.
If a CRC error occurs when reading the device the reading is appended with an !.
The exclamtion point is not kept in the Hi Lo data but the number of CRC errors is recorded.
If it rolls over this is also stated by an R.
If a device or a cable is open the device will state Open if the bus is shorted the setup will state Short and if the data is corrupt it will state Bad.
If every thing is working then it will report OK.
Data can be formatted short:
Sensor 1 +20.06 DegC
or Extended:
Sensor 1 +17.87 DegC Hi+20.18 DegC Low+17.87 DegC
or CSV Celcius data output below,
Sensor 1 +17.93 , DegC, Hi,+20.18, DegC, Low,+17.87, DegC
Typical Fahrenheit output displayed below,
Sensor 1 +64.28 DegF Hi +68.33 DegF Low +64.17 DegF
or both
Sensor 1 +17.87 DegC +64.17 DegF Hi+20.18 DegC +68.33 DegF Low+17.87 DegC +64.17 DegF
CSV is available for whichever mode is selected.
* User settings stored in onboard eerom
The VK011 will display Qkits.com to let you know it has successfully connected. It will then begin to display the data from your connected sensors in the format previously selected. Press the question mark. It will print a list of the four sensor ports. It will say Open next to a sensor port that you are not connected to, whereas if there is a short in the wires, it will say Short, and if you have successfully connected your sensors, it will display each ones unique serial number, the result of the CRC check (any number other than zero means the data is corrupt), whether the data is intact (OK means not corrupt), and the number of CRC errors (if any).
There are three choices when navigating the menu. Displayed at the bottom is Set Next eXit ? and above is the currently selectable mode, for example DegC. This means that if you press S, then it will cycle through the various degrees settings (Fahrenheit, celcius, and both). Press X when you have the one you want selected. To view the next mode option, press N. The choices are degrees system display, CSV (for comma separated values mode, for easy handling if you write your own software, for entry into databases or arrays), short or extended data mode (extended data mode will print the high and low recorded temperature for each sensor, as well as the current temperature), and the sampling rate, which can be set for every second, minute, or a settable amount of seconds, all the way to 99 seconds or 99 minutes.
Additional Information
Additional Information
| SKU | VK011 |
|---|