spacer
QKits - Quality Kits - www.qkits.com - sales@qkits.com About Us   |   Shipping   |   View Cart   |   Your Account   |   Help   
~ Celebrating 18 Years of QualityKits in 2014 ~
  24-Apr-2014  
spacer
spacer


Quick Search

 


Browse Categories

    New Products

    3D Printing
    4D Systems
    ARDUINO┬«
    ARDUINO┬« Compatible
    AUDIO
    Automotive
    Batteries/Chargers
    Clocks & Displays
    Components
    Connectors & Switches
    DC Motor Speed Control
    ELECTRONIC KITS
    Enclosures
    HAMMOND
    Hardware
    Laboratory Kits
    Learning Center
    LED Products
    Light Effects
    MG CHEMICALS
    Miscellaneous
    Power Connectors & Sockets
    Power Supplies
    Pre-Built Modules
    Prototyping Supplies
    Radio Frequency
    Raspberry Pi*
    Record Playback
    Relay Cards
    Remote Control
    RFID Keyless Entry
    Security
    Seven Segment Displays
    Solar and Wind
    Soldering Supplies
    Stepper Motor Control
    SURPLUS
    Test Equipment
    Timers & Controllers
    Tools & Supplies
    Transformers
    USB Devices
    VELBUS
    VELLEMAN MODULES
    Wall Adapters AC to DC

Display Currency
USD US Dollars
Change to Canadian

QualityKits Part #: FK322
FK322: Telephone Cut Off Timer Kit (1 - 20 Min.)
FK322: Telephone Cut Off Timer Kit (1 - 20 Min.)
VIEW LARGER IMAGE
Yes, It's In Stock! This is a KIT and requires assembly!
Cuts off the phone after a set time between 1 and 20 minutes.

Price: USD $11.95

Special: 10-49 items at $10.75 each

Quantity:

With this kit you never have to let your teenager tie up the valuable phone line again.
Cuts off the phone after a set time between 1 and 20 minutes. Gives you a two second warning.
You have twenty seconds to comply, and if you don't, then it disconnects the phone line for about ten seconds.


Gets its power from the phone line itself.


Can fit inside FB17.


PCB dimensions : 3.7 X 2.2

A bit more information,

FK322 telephone cut off timer.

Based on the CMOS 4060 ripple counter.

Uses an RC oscillator in combination with on chip oscillator to achieve a base clock rate of between 6 and 100 HZ, Using CMOS logic permits low power consumption and low voltage operation. A power supply voltage of 3.6 volts obtained from the phone line, regulation is provided by a 3V6 zener diode. Using a 4093 Quad gate allows the tone and tone warning period as well as cutoff timer to be built using simple RC parts. When the timer expires a warning tone is produced for about 2 seconds, then after a few second delay the phone line is disconnected and routed through an on board termination resistor. Until the phone on the FK322 is returned back on hook (for a certain duration), the phone current will be rerouted, basically ending the call. You could change the timing by altering the value of C7 C8 .1 and .027, which form the main time period oscillator.

Longer tone warning by increasing C5 a 10 uF capacitor.

Current draw is around 5mA.

Solder posts are provided for your connections, we recommend using 2 off the shelf phone jacks (female, the type usually found on baseboards), wire one to the incoming and one to the outgoing, this way you can just unplug and move or change in an instant.


Check out these related products:
Telephone Cable w Spade Ends


Price: USD $11.95

Special: 10-49 items at $10.75 each

Quantity: FK322: Telephone Cut Off Timer Kit (1 - 20 Min.)

Display Currency
USD US Dollars
Change to Canadian









   About Us   | View Cart   |   Your Account   |   Help QKits - Quality Kits - www.qkits.com - sales@qkits.com
spacer
~ Celebrating 18 Years of QualityKits in 2014 ~
  24-Apr-2014  
spacer
spacer
  Privacy Policy
QKits Limited - 620 Cataraqui Woods Dr. Unit # 2, Kingston, ON  K7P 1T8 - Canada
Toll Free Order Line: 1-888-464-5487 (no technical help at this number) or EMail: sales@qkits.com
Technical Support: (613) 544-6333 - EMail: tech@qkits.com - Fax: (613) 544-4944
Terms of Use 
Google+